dpp.gif (10671 bytes)

topTable of Contents

Configuring the AT 500
Page 1

Install the handle and spent primer cup. (Figure 4)

Click on image to see larger picture
fig004a.jpg (3636 bytes)

Figure 4 – Installation of the handle and spent primer cup.                   Continued...


Changing Shellplate Position
   
  Your AT 500 is shipped with the "universal" shellplate installed. The "universal" shellplate has four shellholder slots: #1, #2, #3 and #5. This allows you to reload a wide variety of calibers.

  All AT 500 reloaders are shipped with the #1 slot visible. If the caliber you wish to load requires one of the other slots on the shellplate (see the caliber conversion chart to the right to be sure), you may change this by first loosening the brass-tipped setscrew (Figure 5) at the top left side of the shaft, just below the shellplate platform, with the supplied 1/8" hex wrench.

Click on image to see larger picture.
fig005a.jpg (4977 bytes)

Figure 5 – Location of the shellplate bolt setscrew.

  Next, loosen the shellplate bolt with the 1/4" hex wrench. Then reposition the shellplate cover to display the slot you desire to use. The shellplate cover has two dimples (Figure 6) to help you align it with the shellplate.


fig006a.jpg (4528 bytes)

Figure 6 – Locator "dimples" on the AT 500 shellplate cover.

  Tighten the shellplate bolt with the hex wrench – then back the shellplate bolt out about 1/4 turn so that you can rotate the shellplate easily. There should be no looseness or "slop" at this point. When you rotate the shellplate, you should be able to feel and hear the shellplate "click" into place. Re-tighten the brass-tipped setscrew under the shellplate platform to prevent the shellplate bolt from rotating as the shellplate is indexed.

Caliber Conversion Chart
Caliber Shellplate Slot Powder Funnel Locator Button
Rifle Calibers 3 A 3
.222 Rem. 1 A 1
.22-250 3 A 3
.223 Rem. 1 K 1
.240 Wby. Mag. 1 K 1
.243 Win. 1 K 1
.250 Savage 1 K 1
.25-06 1 K 1
.257 Roberts 1 K 1
.257 Ackley Imp. 1 K 1
.270 Win. 1 K 1
.284 Win. 1 K 1
.30-06 1 B 1
.308 1 B 1
.358 Win. 1 B 1
.35 Whelen 1 B 1
.6mm Rem. 1 K 1
6.5-06 1 K 1
6.5x55 1 K 1
7mm-08 1 K 1
7.65x53 1 B 1
7x57 1 K 1
7.7 Arisaka 1 B 1
7mm B.R. 1 K 1
7mm Exp./280 Rem. 1 K 1
7mm Int'l Rim 1 K 1
7.5x55 Swiss 1 B 1
8x57 1 B 1
       
Handgun Calibers      
.22 Rem. Jet 2 A 2
.221 Rem. Fireball 3 A A
.380 ACP 3 F 3
.38 Super 5 F 3
.38/.357 Mag./Max. 2 D 2
.357 SIG 5 F 2
.45 ACP 1 E 1
7 TCU 3 K 3
9mm 5 F 3
9x25 5 F 2
9x21 5 F 3
10mm/.40 S&W 5 W 2
Click here to see larger Caliber Conversion Chart
Top of the next column Continued...

 

contents    Top of the Page

AT 500 Table of Contents
AT 500 Cover Page Configuring the AT 500: 

Changing Shellplate Position 

Caliber Conversion Chart

Changing Primer Size

The Toolhead

AT 500 Parts List
AT 500 Machine Schematic
Suggested Minimum Equipment to Begin Reloading
Reloading Safety
Parts List Setting up the AT 500 to Load:

Rifle Ammunition
    Page 1
    Page 2
    Page 3

Pistol Ammunition
    Page 1
    Page 2

Mounting the AT 500 to Your Bench
The Reloading Process
AT 500 Upgrades
AT 500 Accessories
Contact Information

Dillon Precision Products, Inc.
8009 E. Dillon's Way
Scottsdale, AZ 85260 U.S.A.

Call Toll Free 800-762-3845 or 480-948-8009 ° Fax 480-998-2786
Open 7-6, Monday-Friday; 8-3 Saturday MST
(Open 1400-0100, Monday-Friday; 1500-2200 Saturday GMT)

E-mail Technical Questions to: tech@dillonprecision.com
or try our technical help site at: www.dillonhelp.com/at500.htm
E-mail Order Questions to: dillon@dillonprecision.com
E-Mail for Catalog requests to: catalogs@dillonprecision.com

Have technical questions about Dillon Precision's products? Please send them to dillon@dillonprecision.com

Have comments about this web site? Please send them to comments@happ-eware.com
Copyright © 1998 Happ eWare,  LLC
Last modified: April 28, 1999